UPS 600 + Battery 12-200 Kit

Start UPS are modern, high-precision, economical, reliable and easy to use. If the voltage in the network disappears, it is necessary to use devices that can supply energy to devices in the event of a short-term or complete power outage. The purpose of the devices is to provide the electrical equipment connected to it with an uninterruptible supply of electric energy within the normal range without any interruption in power supply at the time of switching. The norm is a voltage of 220 volts with a sinusoidal signal shape. Start uninterruptible power supplies are a device that combines the functions of a voltage stabilizer, an uninterruptible power supply and a charger for batteries. In the event of a complete voltage loss, the device is in inverter mode - it converts the direct voltage (12, 24, or 48 volts) of the battery into an alternating voltage of 220 volts, which is supplied to consumers. In this case, the shape of the signal that is at the output is a pure sine wave, that is, an ideal signal that the consumer should receive. When the voltage appears in the network again, the device switches from the inverter mode to the stabilization mode. It starts working as a relay-type voltage stabilizer with an input voltage range of 146–285 volts and an accuracy of +/- 10%. Inverter converters of direct voltage to alternating voltage with a built-in relay single-phase voltage stabilizer of the UPS Start series are devices that can provide electrical appliances with not only stable voltage, but also uninterruptible and even higher-quality power supply to consumers in cases of complete power outage. Since the accuracy of the output voltage when operating from the battery is 220 ± 3%, and the output is a pure sine wave. Rubin inverters of the UPS Start series charge the battery when the network is present. When the power is completely lost, the device is in the DC to AC signal converter mode (inverter mode). It converts the direct voltage of the battery to an alternating voltage of 220 volts. In inverter mode, the device consumes the energy of the battery connected to it. Rubin UPS Start inverters are connected to an external battery. A 12-volt battery is used. Using an external battery has advantages over a built-in one: there is no need to contact a service center to replace the old battery with a new one. The inverter itself is portable, easy to transport and is made in a floor-standing design. The front panel of the device is equipped with an elegant LED display that provides information on the parameters of the power grid, the degree of battery discharge, the load level, and overloads. An audible signal notifies about switching on/off the device, about operation in inverter mode, about emergency situations in the network. Features: Protection against transformer overheating and forced cooling. Sound indication of operating modes with the ability to switch off. For correct operation of the UPS, it is necessary that the batteries connected to it (in parallel or in series) have the same degree of charge (discharge). IMPORTANT! This model does not have a built-in (internal) battery. To use the Rubin Start UPS, you must add an external battery of your choice with a nominal capacity of 28 Ah to 200 Ah. By changing the number and capacity of the connected batteries, you can increase or decrease the battery life. The number of connected batteries is limited only by their charging time. This UPS model is designed for floor-standing placement of a set consisting of a UPS and external batteries, necessarily taking into account the recommendations for its placement specified in the operating instructions. With the Rubin Start UPS, we recommend using AGM batteries of the RUBIN brand. These batteries are created using AGM technology, with absorbed electrolyte. The batteries are maintenance-free, sealed, and the resulting gas is recombined, which reduces the frequency of maintenance of this set. The battery case is made of high-strength ABS plastic, which, together with AGM technology, provides high resistance to fire and explosion safety. Due to its universal design, it is suitable for round-the-clock use in a private house, summer house, apartment, office and other premises. The batteries have low self-discharge (up to 3%). The operating voltage is 12 V. The equipment is connected to the batteries with M6 or M8 bolts, which are included in the kit. The service life of the battery depends on the number of cycles, discharge depth, temperature conditions, charging voltage and other factors. If the battery is not used, we recommend charging the battery at least once every six months. The warranty period of the battery is twelve calendar months from the date of sale. Before using the RUBIN battery, we recommend carrying out four discharge/charge cycles to optimize performance. Applications of the Rubin Start+ UPS Kit RUBIN 12-150 AGM: Telecommunication equipment, Circulation pumps, Lighting systems, Household electrical appliances. Features of the Rubin S UPS Kit + RUBIN 12-150 AGM Battery: Intelligent charger, Sine wave output signal, Short circuit and overload protection, Deep battery discharge protection, Cold start, Informative LCD display and sound alarm